Plans for Small Drawer Organizer for Tools Out of Wood
Build the chiffonier
Set your Kreg pocket hole jig for 3/4" thick material. Drill 4 pocket holes on each side (the 14" wide section) of the cabinet shelf and bottom. Use wood glue and i ane/4" pocket pigsty screws to attach the bottom to the cabinet sides so the peak of the bottom lath is i 1/2" above the bottom of the sides. Then attach the cabinet shelf so the height is 28 ane/two" upwardly from the bottom of the cabinet sides. Make certain the cabinet is square.
Add back supports
Add together pocket holes to both sides of the back support pieces. Using wood gum and i one/4" pocket hole screws, adhere one support flush with the back of the cabinet simply under the cabinet shelf. For the second back up, attach information technology to the top back of the chiffonier box. If your closet organizer is being installed nether a shelf that has a board supporting information technology, notch out the top back of your cabinet to fit around it. Then adhere the back support and so information technology is flush with the acme of the cabinet and the notched out section.
Build the face frame
Drill 2 pocket holes on each side of the face frame track. Position them according to the drawing. Use confront clamps to concord them flush with the face frame stiles while securing with wood glue and 1 1/4" pocket hole screws.
Attach the face frame
Place woods glue on the top of the cabinet box. Line the face frame up and so the top is affluent with the top and the pinnacle of the shelf/bottom boards are affluent with the summit of the coordinating confront frame rails. Secure information technology with finish nails into the cabinet box.
Add together groove to drawer box boards
To add the groove for my drawer bottoms, I prefer to use my table saw, but you lot could utilise a router too. For the table saw, I prepare the fence ane/iv" away from the bract and set the bract to 1/4" tall. Then run the drawer box forepart/back and side boards through. And so movement the table saw fence a blade width farther away from the blade and run the boards through again. Repeat until the groove is the same width equally the thickness of you 1/four" plywood.
Build drawer box
Prepare the pocket hole jig for 1/ii" thick material. Drill 2 pocket holes on the terminate of each of the drawer box front/back pieces (both large and pocket-size). Make sure to drill the holes on the reverse side of the board equally the groove so your pocket holes are on the outside of your drawer, keeping them subconscious. Secure ii drawer box side boards to the ends of each drawer box front with wood glue and i" pocket hole screws. Echo for all drawers.
Add the drawer bottoms
Slide the drawer box bottom pieces into the groove.
Cease the drawer boxes
Adhere the drawer box backs to close upward the drawer boxes. Brand sure the bottom sits into the groove. Secure with glue and ane" pocket hole screws.
Finish the drawer fronts
To finish off the drawer fronts, add together edge banding to the edges of the large and small drawer fronts cutting from the three/4" plywood. Trim the excess flush with the plywood.
Prep to install
Set your Kreg jig for 3/4" material. Drill 2 pocket holes on the within top of the cabinet (facing up) to attach the cabinet to the shelf in a higher place. These pocket holes are not meant to concord up the entire weight of the cabinet, but to assistance hold information technology affluent to the shelf above it for install.
Install drawers
Install drawer slides using the Kreg drawer slide jigs. Y'all will need to use drawer slide clips for face frame cabinets or add together a piece of bit 3/four" thick wood within the chiffonier to make the back of the slide flush with the face up frame. The drawers are sized for slides that require 1/2" clearance on each side. Clench the drawer fronts onto the forepart of the drawers. Secure the drawer front end with screws or finish nails in from the within. Then use the cabinet hardware jig to add drawer pulls Make sure the screws go through the drawer front end and the drawer box.
Add shelf (optional)
If y'all want to, you lot can use some of the scraps of 3/4" plywood to cut 1 or ii shelves for the open upper area. Utilize the shelf pin jig to add shelf pivot holes to the top and so cutting shelves to fit. Line the front end with edge banding for a finished wait. We are keeping the area open to create a vanity area for my daughter.
Cease & Enjoy!
Sand and finish your closet organizer. We added an boosted shelf to one side of it and separate the hang bar to have a longer section for dresses and shorter section for shirts. Yous can follow along on our consummate closet makeover at Housefulofhandmade.com!
Install cupboard organizer
Agree your closet organizer up against the shelf. Check for plum and level. Apply shims if needed to get level. Using one 1/four" pocket pigsty screws (for a 3/4" thick cupboard shelf), attach the forepart of the cabinet to the underside of your closet shelf with the pocket holes drilled in the top of the chiffonier. Then using ii 1/2" long cabinet screws, attach the chiffonier to the wall into the studs through the back support pieces. Brand sure to secure the cabinet to the wall through both the back support pieces.
Source: https://learn.kregtool.com/plans/closet-organizer-with-drawers/
0 Response to "Plans for Small Drawer Organizer for Tools Out of Wood"
Post a Comment